Engineering
Engineering, 07.11.2020 23:20, kj44

Please help me--->Assignment directions Visit your local home improvement store, and take a look at the types of cladding available. Assume you need to clad a cabin that is 20 feet (6.1 m) long, 10 feet (3.1 m) wide, and 9 feet (2.7 m) high. (For the purpose of the exercise, the cabin has a flat roof.) It has one door (32 x 80 inches) (81.28 x 203.2 cm) and two windows (28 x 54 inches) (71.12 x 137 cm). Choose five types of cladding; calculate how much you will need for each type and how much each will cost total. Create a chart listing the cladding, amounts, and costs. Also list the benefits and drawbacks of each type of cladding, and then state which one you would want to use for your cabin and why. (Think about what is most important to you—cost, durability, ease of installation, energy efficiency, style, etc.)

Assignment guidelines
Draw a diagram of your cabin. Note where the doors and windows are and the dimensions of the walls. What is the square footage you need to cover, subtracting the area of the door and windows? Choose your claddings: stone, wood, bricks, vinyl siding, stucco, and so on. Your chart should include the cost per unit and how many units you will need. You don’t need to factor in nails, hardware, mortar, or trim.

Submission requirements
Your cabin diagram with proper measurements and calculations should be the first page of your report. The second page should include your chart of five claddings, cost per unit, number of units needed, total cost, benefits, and drawbacks. For a concluding paragraph, note which you would most like on your cabin and why. Please use proper spelling, grammar, and punctuation. Also use complete sentences for the concluding paragraph.

answer
Answers: 1

Other questions on the subject: Engineering

image
Engineering, 04.07.2019 18:10, niyawilliams23
Asingle-geared blanking press has a stroke of 200 mm and a rated capacity of 320 kn. a cam driven ram is assumed to be capable of delivering the full press load at constant force during the last 15 percent of a constant-velocity stroke. the camshaft has an average speed of 90 rev/min and is geared to the flywheel shaft at a 6: 1 ratio. the total work done is to include an allowance of 16 percent for friction a) estimate the maximum energy fluctuation b) find the rim weight for an effective diameter of 1.2 m and a coefficient of speed fluctuation of 0.10
Answers: 1
image
Engineering, 04.07.2019 18:10, qwertylol12345
Different types of steels contain different elements that alter the characteristics of the steel. for each of the following elements, explain what the element does when alloyed with steel.
Answers: 2
image
Engineering, 04.07.2019 18:10, caitlynnpatton1208
Water in a partially filled large tank is to be supplied to the roof top, which is 8 m above the water level in the tank, through a 2.2-cm-internal-diameter pipe by maintaining a constant air pressure of 300 kpa (gage) in the tank. if the head loss in the piping is 2 m of water, determine the discharge rate of the supply of water to the roof top in liters per second.
Answers: 3
image
Engineering, 04.07.2019 18:10, soreese02
An ideal otto cycle with air as the working fluid has a compression ratio of 8. the minimum and maximum temperatures in the cycle are 300 k and 1340 k. use constant specific heats at room temperature to determine (a) the amount of heat transferred to the air during the heat- addition kj/kg, (b) the thermal efficiency, and (c) the thermal efficiency of a carnot cycle ope limits. process, in rating between the same temperature
Answers: 2
Do you know the correct answer?
Please help me--->Assignment directions Visit your local home improvement store, and take a look...

Questions in other subjects:

Konu
Biology, 26.09.2019 04:20