Engineering
Engineering, 23.04.2020 01:23, swaggernas

A three storey structure having a square footprint of 225 m2 is constructed on a clayey deposit. The structure is planned to be supported by square isolated footings having a width of 2m and spaced at 5m center to center. A typical borehole indicates that the soil consists of 2m fill layer at the top (=17KN/m3) followed by a very stiff clay layer 2m thick (sat=18.5KN/m3) underlain by a normally consolidated soft clay layer of 4.5m thickness (sat=17KN/m3) followed by a rock layer extending down to the bottom of borehole. The foundations are laid on top of the stiff clay layer. Water table is located at the top of the stiff clay layer. Undisturbed samples were taken from the middle of each clay layer and consolidation tests done on undisturbed samples indicated the following:

 Stiff Clay: Cc=0.15; Cs = 0.02; Pc = 120 kPa; e0=0.9
 Soft Normally Consolidated Clay: Cc=0.38; Cs = 0.06; e0=1.0

a) Draw a sketch representing the various problem components.

b) The isolated foundations are subjected to a stress of 140 kPa. Calculate the consolidation settlement. Consider the very stiff clay as one layer and divide soft clay layer into two equal sub-layers. Calculate settlement under one typical foundation.

c) What would be the maximum additional stress applied on a central foundation from two neighboring foundations (situated at the left and right sides of the central foundation). Is it necessary to consider the additional stresses from neighboring foundations in the settlement calculations?

d) A concern is the differential settlement between isolated adjacent footings. It was decided to change the design to have the structure founded on a raft foundation subjected to a stress of 45 kPa. Compute the consolidation settlement and comment on the results.

answer
Answers: 3

Other questions on the subject: Engineering

image
Engineering, 04.07.2019 18:10, leomessifanboy678
The filament of an incandescent lamp has a temperature of 2000k. calculate the fraction of radiation emitted in the visible light band if the filament is approximated as blackbody
Answers: 2
image
Engineering, 04.07.2019 18:10, samanthabutryn
Which one from below is not one of the reasons of planning failures? (clo3) a)-planner is careless. b-planner spend less time in the field but more time on the desk c)-planner is not qualified d)-planner does not have sufficient time to properly plan
Answers: 3
image
Engineering, 04.07.2019 18:20, krojas015
Asolid cylinder is concentric with a straight pipe. the cylinder is 0.5 m long and has an outside diameter of 8 cm. the pipe has an inside diameter of 8.5 cm. the annulus between the cylinder ad the pipe contains stationary oil. the oil has a specific gravity of 0.92 and a kinematic viscosity of 5.57 x 10-4 m2/s. most nearly, what is the force needed to move the cylinder along the pipe at a constant velocity of 1 m/s?
Answers: 3
image
Engineering, 04.07.2019 19:10, batmanmarie2004
Afoot bridge is made as a simple deck, 4 m long, with a cross section 2 m (wide) and 20 cm thick, and made of wood. the deck is supported at the two ends. the maximum load allowable on the bridge is 10 tons, provided it is uniformly distributed on the deck. to sense this load, a strain gauge is placed at the center of the bridge and its resistance is monitored. if the sensor has a nominal resistance of 350 s2 and a gauge factor of 3.6, what is the reading of the strain gauge at maximum load? the modulus of elasticity for the wood used in the construction is 10 gpa.
Answers: 2
Do you know the correct answer?
A three storey structure having a square footprint of 225 m2 is constructed on a clayey deposit. The...

Questions in other subjects:

Konu
Mathematics, 16.10.2019 19:30
Konu
Mathematics, 16.10.2019 19:30