Engineering
Engineering, 01.10.2019 01:20, maria7515

A200 mw combined cycle gas turbine (ccgt) power generation station is considering the addition of a carbon capture and storage (ccs) system. the power generation station has a capacity factor of 90% and a heat rate of 8530 btu/kwh (higher heating value). the ccs system will remove and stores 85% of the co2 produced by the power generation station. however, the ccs system will reduce the efficiency of the plant by 6%. for example a plant with 32% efficiency without a ccs system would have 26% efficiency with a ccs system. the rated capacity of the plant will remain at 200 mw after the installation of the ccs. assume the natural gas used to fuel the ccgt power generation station is composed of 95% methane (ch4) and 5% nitrogen (n2) on a volumetric basis and has a higher heating value of 52.8 mj/kg. it is purchased for $3.50/mbtu. a. what is the mass fraction of carbon (c) in the natural gas (kg/kgna)? b. what is the co2 emission factor for the natural gas fuel (kgco2/mbtung)? c. what are the co2 emissions per mwh of electricity delivered for the current power generation station (mgco2/mwh)? d. what are the annual co2 emissions of the current generating station (mgcoz/y)? e. what would be the co2 emissions per mwh of electricity delivered if the ccs were installed (mgco2/mwh)? f. what would be the annual co2 emissions if the ccs is installed (mgooz/y)? g. how many metric tons of co2 emissions would be avoided annually if the ccs is installed (mg0oz/y)? h. what is the increased cost of fuel per year of electricity generated as a result of the ccs system (106 $/y)? i. what is the increased cost of fuel per metric ton of co2 avoided ($/mg002)?

answer
Answers: 2

Other questions on the subject: Engineering

image
Engineering, 04.07.2019 19:10, nida7864
An engine, weighing 3000 n, is supported on a pedestal mount. it has been observed that the engine induces vibration into the surrounding area through its pedestal at the maximum operating speed. determine the stiffness of the dynamic vibration absorber spring in (n/m) that will reduce the vibration when mounted on the pedestal. the magnitude of the exciting force is 250 n, and the amplitude of motion of the auxiliary mass is to be limited to 2 mm note: in this question type-in right numbers, no decimals, no fractions, no unit. approximate to right number if needed
Answers: 3
image
Engineering, 04.07.2019 19:20, diawia
Air at a pressure of 1atm and a temperature of 40 c is in parallel flow over the top surface of a flat plate that is heated to a uniform temperature of 120 c. the plate has a length of 0.40m (in the flow direction) and a width of 0.15m. the reynolds number based on the plate length is 50, 000. what is the rate of heat transfer from the plate to the air? if the free stream velocity of the air is doubled and the pressure is increased to 10 atm what is the rate of heat transfer?
Answers: 2
image
Engineering, 05.07.2019 19:10, justin20080
Tech a says never use a water hose to clean up dust after a repair. tech b says never use a floor scrubber to clean up dust after repairs. who is correct?
Answers: 1
image
Engineering, 06.07.2019 03:10, brookealexis5768
Oxygen at 300 kpa and 400 k is in a closed system with an initial volume of 0.1 m3. is now compressed in a polytropic process, with exponent of n 1.2, to a temperature of 500 k. calculate: a) the boundary work done during the compression, in kj b) the heat transfer during the compression, in kj
Answers: 3
Do you know the correct answer?
A200 mw combined cycle gas turbine (ccgt) power generation station is considering the addition of a...

Questions in other subjects:

Konu
Mathematics, 17.02.2021 06:20
Konu
Mathematics, 17.02.2021 06:20