Physics, 16.12.2019 22:31, calebvaughn924

How is temperature defined in terms of molecular action?

Answers: 3

Show answers

Answers

answered: Guest

most voltage drop calculators want the distance between the source and destination. then internally, they double it so both the source and return wires are calculated. but you need to know which distance the calculator uses so you're not half of what you should be or double what you should be.

most circuit breakers will not take a #6 directly, so the electrician will have to splice on a smaller pigtail. you also have to upsize the grounding wire when you upsized the ungrounded (hot) wire (see note in 250.122). this will preclude using most cable assemblies, as a cable with #6 copper will most likely only have a #10 grounding conductor. you need a #6 grounding conductor if the circuit is 20a. a #8 cable is no better, as it will have a #10 grounding conductor too. but most 20a breakers will take a #8 directly.

in your related post, you didn't say what type of load this is. if it is a light or heater, voltage drop won't be a big issue. if this is a motor, the current needs are huge at startup and the voltage drop can pose a problem. if this is a motor, knowing if the motor is under much load during startup will answer the voltage drop effect (a saw is easier to start than a compressor).

answered: Guest

when heated, the valance electrons increased their speed and transferred the heat from electron to electron. i just took the test.

answered: Guest

Which of the following are risk factors for emphysema ? correct answer : a and and c good luck and have a nice benevolentpuppy day! : )

answered: Guest

force is based upon mass and acceleration.the statement is not always true.

it can be explained from newton's second law of motion.

as per newton's second law of motion the rate of change of momentum is directly proportional to the applied force and takes place along the direction of force.

mathematically it can be written as -

$f\alpha \frac{dp}{dt}$

⇒ $f= k \frac{dp}{dt}$

here k is the proportionality constant whose value is 1.

$f=\frac{dp}{dt}$

$f= \frac{d[mv]}{dt}$

$f= m\frac{dv}{dt} +v\frac{dm}{dt}$

$f=ma+v\frac{dm}{dt}$ [a is the acceleration=dv/dt]

hence we see that force not only depends on mass and acceleration but also on velocity and rate of change of mass. force f will depend on mass and acceleration only when mass is constant.

hence the statement that force is based upon mass and acceleration is false.

Other questions on the subject: Physics

Physics, 22.06.2019 08:00, levilugar

Who was the first scientist to measure speed as distance over time?

Answers: 1

continue

Physics, 22.06.2019 09:00, reyesortiz6955

In a heat engine if 1000 j of heat enters the system the piston does 500 j of work, what is the final internal energy of the system if the initial energy was 2000 j? 1. write the equation 2.list out your known variables 3.plug the numbers into the equations 4.solve 5.write your solution statement that includes initial energy and final

Answers: 1

continue

Physics, 22.06.2019 16:00, LikeIke2859

In which of the following is positive work done by a person on a suitcase

Answers: 1

continue

Physics, 22.06.2019 20:50, dorkygirl

An ideal otto cycle has a compression ratio of 8. at the beginning of the compression process, air is at 95 kpa and 27°c, and 750 kj/kg of heat is transferred to air during the constant-volume heat-addition process. assuming constant specific heats at room temperature, determine (a) the pressure and temperature at the end of the heat-addition process, (b) the net work output, (c) the thermal efficiency, and (d) the mean effective pressure for the cycle. (4390 kpa, 1730 k; 423 kj/kg; 56.4%; 534 kpa)