Physics
Physics, 11.10.2021 05:00, bb1235626

STATE 2 APPLICATIONS OF CIRCULAR MOTION

answer
Answers: 3

Other questions on the subject: Physics

image
Physics, 21.06.2019 14:10, F00Dislife
Amachinist needs to remove a tight fitting pin of material a from a hole in a block made of material b. the machinist heats both the pin and the block to the same high temperature and removes the pin easily. what statement relates the coefficient of thermal expansion of material a to that of material b? a) the situation is not possible, heating block b will shrink the hole in the material as the material expands with increasing temperatureb) material b has the same coefficient of expansion as does material ac) material b has a negative coefficient of expansion and a has a positive coefficient of expansiond) material a has a greater coefficient of expansion than does material be) material b has a greate
Answers: 1
image
Physics, 23.06.2019 08:30, 01222002
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
image
Physics, 23.06.2019 10:00, nida7864
Plz explain what friction, corollas, and a low pressure gradient does to an air parcel. what is 1+1=
Answers: 1
image
Physics, 23.06.2019 10:30, tamikagoss22
Can someone answer my last question i posted? on my last post? my hw is due tomorrow and i’m confused.
Answers: 1
Do you know the correct answer?
STATE 2 APPLICATIONS OF CIRCULAR MOTION...

Questions in other subjects: