Physics, 24.06.2021 16:30, jackkie10

Three children are riding on the edge of a merry-go-round that is 182 kg, has a 1.60 m radius, and is spinning at 15.3 rpm. The children have masses of 17.4, 28.5, and 32.8 kg. If the child who has a mass of 28.5 kg moves to the center of the merry-go-round, what is the new angular velocity in rpm

Answers: 3

Show answers

Other questions on the subject: Physics

Physics, 21.06.2019 22:00, Angelo1660

Air is held within a frictionless piston-cylinder container, which is oriented vertically. the mass of the piston is 0.45 kg and the cross-sectional area is 0.0030 m2. initially (state 1) the pressure of the gas is sufficient to support the weight of the piston as well as the force exerted by the atmospheric pressure ( 101.32 kpa). the volume occupied by the air within the cylinder in state 1 is 1.00 liter. one end of a spring (with spring constant k = 1000 n/m) is attached to the top of the piston, while the other end of the spring is attached to a stage that can move vertically. initially the spring is undeflected and therefore exerts no force. then the stage is then moved quasistatically downward a distance of 10.0 cm, at which point the system reaches state 2. the piston-cylinder is not insulated; rather it remains in diathermal contact with the surroundings, which are at a constant temperature of 300 k. what is the change of pressure within the container?

Answers: 3

continue

Physics, 22.06.2019 04:00, NateTheBeast12

It can take some of those large , industrial vehicles up to feet to stop when traveling only 60 mph, and therefore , you shoukd be mindful to not be jn the traffic right in front of them a. 100 feet b. 200 feet c. 335 feet d. 425 feet

Answers: 1

continue

Physics, 22.06.2019 04:30, loloi83

Acrow drops a 0.11kg clam onto a rocky beach from a height of 9.8m. what is the kinetic energy of the clam when it is 5.0m above the ground? what is its speed at that point?

Answers: 1

continue

Physics, 23.06.2019 08:30, 01222002

Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28

Answers: 2

continue

Do you know the correct answer?

Three children are riding on the edge of a merry-go-round that is 182 kg, has a 1.60 m radius, and i...