Physics, 23.06.2021 02:20, datzmypupppup

HEL WILL MARK BRAINLIEST The coating on the head of a match is highly flammable. When it burns, it releases a great deal of energy. However, before the match can burn, it must gain a small amount of energy from a spark. That spark is typically produced by striking (rubbing) the match head against a rough surface.

Sketch and describe a potential energy diagram that represents the striking and burning of the match. Remember to label the diagram with the energy changes that occur. Your answer must include the potential energy diagram and a written description. (Note: you do not have to use actual energy values.)

Answers: 2

Show answers

Answers

answered: Guest

a solenoid is created by wrapping a l = 90 m long wire around a hollow tube of diameter d = 4.5 cm. the wire diameter is d = 0.9 mm. the solenoid wire is then connected to a power supply so that a current of i = 9 a flows through the wire.

randomized variablesl = 90 m

d = 4.5 cm

d = 0.9 mm

i = 9 a

write an expression for the number of turns, n, in the solenoid. you do not need to take into account the diameter of the wire in this calculation.

calculate the number of turns, n, in the solenoid.

write an expression for the length of the solenoid (l2) in terms of the diameter of the hollow tube d.

calculate the length of the solenoid (l2) in meters.

calculate the magnitude of the magnetic field at the center of the solenoid in teslas.

explanation:

answered: Guest

a 2,000 calorie based diet.

answered: Guest

Gas will most likely fill the container

answered: Guest

force is based upon mass and acceleration.the statement is not always true.

it can be explained from newton's second law of motion.

as per newton's second law of motion the rate of change of momentum is directly proportional to the applied force and takes place along the direction of force.

mathematically it can be written as -

$f\alpha \frac{dp}{dt}$

⇒ $f= k \frac{dp}{dt}$

here k is the proportionality constant whose value is 1.

$f=\frac{dp}{dt}$

$f= \frac{d[mv]}{dt}$

$f= m\frac{dv}{dt} +v\frac{dm}{dt}$

$f=ma+v\frac{dm}{dt}$ [a is the acceleration=dv/dt]

hence we see that force not only depends on mass and acceleration but also on velocity and rate of change of mass. force f will depend on mass and acceleration only when mass is constant.

hence the statement that force is based upon mass and acceleration is false.

Other questions on the subject: Physics

Physics, 21.06.2019 18:20, arixox

An input force of 7 n is applied to a machine with a mechanical advantage of 1.75. what is the maximum the machine could lift? 12.25 n7n7.25 n26.2 n

Answers: 1

continue

Physics, 22.06.2019 14:30, gabriellam20

A10nc charge sits at a point in space where the magnitude of the electric field is 1500 n/c. what will the magnitude of the field be if the 10 nc charge is replaced by a 20 nc charge? assume the system is big enough to consider the charges as small test charges.

Answers: 1

continue

Physics, 22.06.2019 15:40, triddi666

If an electric circuit is not grounded it is best to reach out and touch it to provide the ground a. true or b. false

Answers: 2

continue

Physics, 22.06.2019 18:30, Felici8617

4. now look at the green lines you created by connecting the three boiling point data points and the three melting point data points. for each of these lines, describe any trends you see. 5. locate the elements on your periodic table that you circled in green on your graph. what term or description would you use to identify these elements with respect to the periodic table? 7. using the room temperature line (orange line) and your periodic table, make lists that identify the state of matter (gas, liquid, or solid) in which each element you plotted exists at room temperature. explain your answers.

Answers: 2

continue

Do you know the correct answer?

HEL WILL MARK BRAINLIEST The coating on the head of a match is highly flammable. When it burns, it...