Match the terms and the definitions
Lesson 3.04
Question 11 options:
Equino...
Physics, 03.04.2021 04:40, Saberabuomar2007
Match the terms and the definitions
Lesson 3.04
Question 11 options:
Equinoxes
Seasons
Summer Solstice
Winter Solstice
1.
The earth is in a position so that the North Pole is tilted most directly toward the sun.
2.
The tilt and revolution of the earth as it moves around the sun cause
3.
This is the day of the year with the least amount of daylight, which is due to the tilt of the earth's axis.
4.
Days and nights are equal length, and the noon sun is directly overhead.
Answers: 2
Physics, 22.06.2019 19:30, unknownday7
What characteristics of hv2112 make it the best candidate to be classified as a thorne-zytkow object?
Answers: 3
Physics, 22.06.2019 19:50, fili20
The heater element of a 120 v toaster is a 5.4 m length of nichrome wire, whose diameter is 0.48 mm. the resistivity of nichrome at the operating temperature of the toaster is 1.3 × 10-6 ω·m. the toaster is operated at a voltage of 120 v. (a) what is the power drawn by the toaster? (b) if the cost of electricity is 12 ¢ per kilowatt-hour, and it takes 2 minutes to toast bread, how much does it cost for toasted bread? (c) when the heater element is at room temperature, is the resistivity in the nichrome wire greater than, less than, or equal to it’s resistivity when at operating temperature? explain.
Answers: 3
Physics, 23.06.2019 08:30, 01222002
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
Physics, 04.08.2019 08:00
Biology, 04.08.2019 08:00
Mathematics, 04.08.2019 08:00
History, 04.08.2019 08:00