Physics
Physics, 11.03.2021 01:00, richardcarmona54

WILL GIVE BRAINLIST 3) In the food chain below, Which level has the least amount of energy?
E)Herbivore
A) Secondary Consumer
O) Producer
4) Which of the following is an ecosystem?
M) A moose
I) The biotic factors in the rainforest
B) A corn Field
I thinks it A and I

answer
Answers: 3

Other questions on the subject: Physics

image
Physics, 22.06.2019 06:40, alicemareus
Determine the change in width a, height b, thickness t when a plate is subjected to the uniform distributed load and is made of material having modulus of elasticity e=230 gpa and poisson's ratio ν=1/3. given : a=400 mm and b= 300 mm also the uniformly distributed load in downward y direction of plate is 2 mn/m and in the positive x direction is 3 mn/m and t=20 mm
Answers: 1
image
Physics, 23.06.2019 03:30, alejandra340
The applied force of 3 washers will increase the applied force on the car to n.
Answers: 1
image
Physics, 23.06.2019 05:00, LilFlamingo247
What about a rubber band, can it change its shape? is it a solid?
Answers: 2
image
Physics, 23.06.2019 08:30, 01222002
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
Do you know the correct answer?
WILL GIVE BRAINLIST 3) In the food chain below, Which level has the least amount of energy?
...

Questions in other subjects:

Konu
Mathematics, 24.04.2020 17:05
Konu
Mathematics, 24.04.2020 17:05