Learning Task 5: Compose a jingle to remind us on the different principles
and safety rules in food preservation. You can also make some steps that
will match in your created jingle.
Learning Task 6: Make a slogan about the safety rules in food preserva-
tion.
Learning Task 7: Conduct an interview to your household members or oth-
er people that is knowledgeable in food preservation to give tips and points
to ponder while doing food preservation.
PIVOT 4A CALABARZON
22
Answers: 2
Physics, 22.06.2019 11:30, swaggyd6603
Write down two additional questions about earth's magnetic field that will make your presentation more informative.
Answers: 1
Physics, 22.06.2019 19:00, deonnaturner68p7hz7y
The direction of the current in an alternating current circuit remains constant. is direct. changes repeatedly. changes randomly.
Answers: 1
Physics, 23.06.2019 08:30, 01222002
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
Physics, 23.06.2019 13:20, punkinrichard1oxon2i
Two wooden members of 80 × 120-mm uniform rectangular cross section are joined by the simple glued scarf splice shown. knowing that β = 22° and that the maximum allowable stresses in the joint are, respectively, 400 kpa in tension (perpendicular to the splice) and 690 kpa in shear (parallel to the splice), determine the largest centric load p that can be applied using mohr's circle. (round the final answer to two decimal places.)
Answers: 1
Learning Task 5: Compose a jingle to remind us on the different principles
and safety rules in food...
Mathematics, 09.12.2020 03:00
Mathematics, 09.12.2020 03:00
Computers and Technology, 09.12.2020 03:10