Physics, 03.11.2020 16:20, jor66

The tub of a washer goes into its spin cycle, starting from rest and gaining angular speed steadily for 7.00 s, at which time it is turning at 5.00 rev/s. At this point, the person doing the laundry opens the lid, and a safety switch turns off the washer. The tub smoothly slows to rest in 8.00 s. Through how many revolutions does the tub turn while it is in motion

Answers: 1

Show answers

Answers

answered: Keelana

The tub of the washer does 37.5 revolutions while it is in motion.

Explanation:

At first we assume that the tub accelerates and decelerates uniformly. In this case, it is required to determine the number of revolutions done by the tub by means of the following equations of motion:

Acceleration

$\ddot n_{1} = \frac{\dot n_{1}-\dot n_{1,o}}{t_{1}}$ (Eq. 1)

Where:

$\ddot n_{1}$ - Angular acceleration experimented by the tub, measured in revolutions per square second.

$\dot n_{1,o}$ , $\dot n_{1}$ - Initial and final angular velocities of the tub, measured in revolutions per second.

$t_{1}$ - Acceleration time, measured in seconds.

$\Delta n_{1} = \dot n_{1,o}\cdot t_{1}+\frac{1}{2}\cdot \ddot n_{1}\cdot t_{1}^{2}$ (Eq. 2)

Where $\Delta n_{1}$ is the change in angular position of the tub during acceleration, measured in revolutions.

Deceleration

$\ddot n_{2} = \frac{\dot n_{2}-\dot n_{1}}{t_{2}}$ (Eq. 3)

Where:

$\ddot n_{2}$ - Angular acceleration experimented by the tub, measured in revolutions per square second.

$\dot n_{1}$ , $\dot n_{2}$ - Initial and final angular velocities of the tub, measured in revolutions per second.

$t_{2}$ - Deceleration time, measured in seconds.

$\Delta n_{2} = \dot n_{1}\cdot t_{2}+\frac{1}{2}\cdot \ddot n_{2}\cdot t_{2}^{2}$ (Eq. 4)

If we know that $\dot n_{1,o} =0\,\frac{rev}{s}$ , $\dot n_{1} = 5\,\frac{rev}{s}$ , $t_{1} = 7\,s$ , $\dot n_{2} = 0\,\frac{rev}{s}$ and $t_{2} = 8\,s$ , then the amount of revolutions done by the tub during each phase is, respectively:

(Eq. 1)

$\ddot n_{1} = \frac{5\,\frac{rev}{s}-0\,\frac{rev}{s} }{7\,s}$

$\ddot n_{1} = \frac{5}{7}\,\frac{rev}{s^{2}}$

(Eq. 3)

$\ddot n_{2} = \frac{0\,\frac{rev}{s}-5\,\frac{rev}{s} }{8\,s}$

$\ddot n_{2} = -\frac{5}{8}\,\frac{rev}{s^{2}}$

(Eq. 2)

$\Delta n_{1} = \left(0\,\frac{rev}{s} \right)\cdot (7\,s)+\frac{1}{2}\cdot \left(\frac{5}{7}\,\frac{rev}{s^{2}}\right) \cdot (7\,s)^{2}$

$\Delta n_{1} = \frac{35}{2}\,rev$

(Eq. 4)

$\Delta n_{2} = \left(5\,\frac{rev}{s} \right)\cdot (8\,s)+\frac{1}{2}\cdot \left(-\frac{5}{8}\,\frac{rev}{s^{2}}\right) \cdot (8\,s)^{2}$

$\Delta n_{2} = 20\,rev$

The total amount of revolutions done by the tub while it is in motion is:

$\Delta n_{T} = \Delta n_{1}+\Delta n_{2}$

$\Delta n_{T} = 37.5\,rev$

The tub of the washer does 37.5 revolutions while it is in motion.

answered: Guest

Ifeel like lily and ledbetter had a fair pay act just because it was necessary especially at those times

answered: Guest

the grams of oxygen gas that can be produced is 20.6 grams of o₂

calculation

2liclo₃ → 2 licl + 3 o₂

step 1: find the moles of liclo₃

moles = mass÷ molar mass

from periodic table the molar mass of liclo₃ =6.9 +35.5 +(16 x3) =90.4 g/mol

moles=38.7 g÷90.4 g/mol=0.4281 moles

step 2: use the mole ratio to calculate the moles of o2

from equation above, liclo₃: o₂ is 2: 3

therefore the moles of o₂=0.4281 moles x3/2 =0.6422 moles

step 3: find mass of o₂

mass= moles x molar mass

from periodic table the molar mass of o₂ = 16 x2= 32 g/mol

mass=0.6422 moles x 32 g/mol = 20.6 grams of o₂

Other questions on the subject: Physics

Physics, 22.06.2019 01:50, ssuereichard

Aregion of space in which a measurable gravitational force is indicated by the force exerted on a test mass is called

Answers: 1

continue

Physics, 22.06.2019 06:30, bluevibe

2kg of refrigerant 134a undergoes a polytropic process in a piston-cylinder assembly from an initial state of saturated vapor at 2 bar to a final state of 12 bar, 80 degree c. a)determine the work for the process in kj. b)sketch the process on a p-v diagram.

Answers: 2

continue

Physics, 22.06.2019 08:20, cutechickens13

A3030 cmcm wrench is used to loosen a bolt with a force applied 0.30.3 mm from the bolt. it takes 6060 nn to loosen the bolt when the force is applied perpendicular to the wrench. how much force would it take if the force was applied at a 3030 degree angle from perpendicular? a 3030 cmcm wrench is used to loosen a bolt with a force applied 0.30.3 mm from the bolt. it takes 6060 nn to loosen the bolt when the force is applied perpendicular to the wrench. how much force would it take if the force was applied at a 3030 degree angle from perpendicular?

Answers: 3

continue

Physics, 22.06.2019 11:00, sydneyclack

Alarge box of mass m is pulled across a horizontal frictionless surface by a horizontal rope with tension t. a small box of mass m sits on top of the large box. the coefficients of static and

Answers: 1

continue

Do you know the correct answer?

The tub of a washer goes into its spin cycle, starting from rest and gaining angular speed steadily...