Physics, 31.10.2019 21:31, zoewilliamss26
Brainliest + 20 points for a correct answer - this is probably super easy but i'm just not the smartest
light reflects off many objects. which model of light behavior best explain this effect?
(a.) particle model
(b.) wave model
(c.) magnetic model
(d.) electric model
Answers: 2
Physics, 23.06.2019 06:50, paaoolav
Un conductor circula por una carretera en una velocidad de 90 km/h y b que se enciende la luz amarilla de un semáforo situado una distancia de 150 m. si el semáforo tarda tres segundos en cambiar a rojo el coche frena con una aceleración de 2 m por segundos 2¿ cometer una infracción ese conductor?
Answers: 1
Physics, 23.06.2019 08:00, 19thomasar
Acar going 30 m/s to 70 m/s in 10 seconds calculate the acceleration of the car
Answers: 2
Physics, 23.06.2019 08:30, 01222002
Atension test was conducted on a specimen of aisi 1020 hot-rolled steel having an initialdiameter of 9.11 mm. representative test data are given in table1in the form of force and engineering strain. for strain the extensometer gage length was li= 50.8 mm. in addition, minimumdiameters were measuredmanually with a micrometer in the necked region at several points during the test. after fracture, thebroken halves were reassembled, and the following measurements were made: (1) marks originally 25.4 mm apart and on opposite sides of the necked regionwere 38.6 mm apart due to the lengthwise stretching in the specimen; (2) similar marks originally 50.8 mm apart were 70.9 mmapart; (3) the final minimum diameter in the necked region was 5.28 mma) determine the following material properties: elastic modulus, 0.2% offset yield strength, ultimate tensile strength, percent elongation, and percent reduction in area. b) assume that the test was interrupted upon reaching a strain u = 0.007, and the specimen unloaded to zero force. estimate the elastic strain recovered and the plastic strain remaining. also, what would the new length of the original 50.8 mm gage section. hint: might save time/effort to use excel, mathcad, matlab, etc. to solve part a)table1 data and analysis for a tension test on aisi 1020 hot-rolled steeltest dataforce (p, kn)1. 0.002. 6.673. 13.344. 19.135. 17.796. 17.217. 17.538. 17.449. 17.2110. 20.7711. 24.2512. 25.7113. 25.7514. 25.0415. 23.4916. 21.3517. 18.9018. 17.39engr. strain (ε)1. 02. 0.00053. 0.00104. 0.00155. 0.00236. 0.00317. 0.00508. 0.00709. 0.010010. 0.049011. 0.125012. 0.218013. 0.234014. 0.306015. 0.330016. 0.348017. 0.360018. 03660diameter (d, mm)1. 9.112. 9.113. 9.114. 9.115. 9.116. 9.117. 9.118. 9.119. 9.1110. 8.8911. 8.8912. 8.2613. 8.2614. 7.6215. 6.9916. 6.3517. 5.7218. 5.28
Answers: 2
Brainliest + 20 points for a correct answer - this is probably super easy but i'm just not the smart...
Chemistry, 30.05.2021 18:20
Mathematics, 30.05.2021 18:20
Geography, 30.05.2021 18:20
Mathematics, 30.05.2021 18:20
World Languages, 30.05.2021 18:20