Mathematics
Mathematics, 18.06.2021 15:10, insaneke

Question: find x
HELP ASAP


Question: find x HELP ASAP

answer
Answers: 2
Show answers

Other questions on the subject: Mathematics

image
Mathematics, 21.06.2019 18:00, angeladominguezgarci
Which ordered pair is a solution to the system of linear equations? 2x + 3y= 6 –3x + 5y = 10
Answers: 1
continue
image
Mathematics, 21.06.2019 19:00, Olavarriafamily1
The figures below are made out of circles, semicircles, quarter circles, and a square. find the area and the perimeter of each figure and give your answers as a completely simplified exact value in terms of π (no approximations).
Answers: 1
continue
image
Mathematics, 21.06.2019 20:40, corrah15
Which function has an inverse function? a. f(x)= |x+3|/5 b. f(x)= x^5-3 c. f(x)= x^4/7+27 d. f(x)= 1/x²
Answers: 1
continue
image
Mathematics, 22.06.2019 00:10, jocelynfray16
Change negative exponents to positive. then solve. round to four decimal places
Answers: 3
continue
Do you know the correct answer?
Question: find x
HELP ASAP
...

Questions in other subjects:

Konu
Biology, 26.07.2019 17:20
Terrance, whose birth mother drank heavily throughout pregnancy, has a thin upper lip, short eyelid openings, a small head, and a smooth philtrum. his physical growth has been slow...
Konu
Physics, 26.07.2019 17:20
"for a first order instrument with a sensitivity of .4 mv/k and a time" constant of 25 ms, find the instrument’s response as a function of time for a sudden temperature increase fr...
Konu
Mathematics, 26.07.2019 17:20
You and your friend are at a shooting range. you ran out of bullets. your friend still has two bullets left but magically lost his gun. somehow you both agree to put the two bullet...
Konu
Engineering, 26.07.2019 17:20
Initially there are 3 [kg) of gas at a pressure of 200 [kpa] and specific volume of 1.5 [m3/kgl contained within a piston cylinder assembly. the gas undergoes a polytropio process...
Konu
Engineering, 26.07.2019 17:20
In machining, if the cost to purchase/regrind the cutting tool=$0.00, the optimum speed for machining time minimization would be different from the optimum speed for production cos...
Konu
Engineering, 26.07.2019 17:20
In turning, if the spindle speed (spindle rpm) increases by a factor of four, while the feed rate decreases by a factor of four, will the ideal surface roughness change? i. yes. i...
Konu
Engineering, 26.07.2019 17:20
Oil, with a density of ρ = 900 kg m=3 and a kinematic viscosity of v = 0.1 m^2 s^-1, flows at a volume flow rate of q 0.2 m^3 s^-1 through 500 m of 200 mm diameter pipe which has a...
Konu
Engineering, 26.07.2019 17:20
What is an involute profile and why is it used in gear tooth design?...
Konu
Engineering, 26.07.2019 17:20
If i can live with a 3% probability of failure, select a ball bearing design (independent of shaft diameter that will carry a 120 ib load at 3000 rpm. how long can i expect the sel...
Konu
Engineering, 26.07.2019 17:20
Determine the diameter of a cylindrical capillary tube needed to observe a 0.4" rise for water if the contact angle is 12°...
Other tasks in the category: Mathematics More task
See results (0)