Engineering
Engineering, 31.05.2021 14:40, scottykinkade7860

Design and write an Octave function (you can specify any name) that performs the following functionality: 1. Accepts three input parameters that specify the start element in the array, the end element in the array and the number of points in total between the start and end points. [6] 2. Check if three input arguments are provided. If insufficient input arguments are provided, then print an error message and exit the function. [4] 3. Check that the end input parameter is greater than the start input parameter. If the start input parameter is greater than or equal to the end input parameter, then print an error message and exit the function. [4] 4. Create two row vectors (x and y) with the input arguments. Use the Octave command that returns a row vector with linearly spaced elements [10] 5. Use the Octave command that creates matrices corresponding to a full 2-D grid. [4] 6. Use the Octave command that plots a 3-D wireframe mesh with underlying contour lines [4] 7. Label the x, y and z axis with a font size of 12. [3]


Design and write an Octave function (you can specify any name) that performs the following function

answer
Answers: 2

Other questions on the subject: Engineering

image
Engineering, 03.07.2019 15:10, EmilySerna
Heat is added to a piston-cylinder device filled with 2 kg of air to raise its temperature 400 c from an initial temperature of t1 27 cand pressure of pi 1 mpa. the process is isobaric process. find a)-the final pressure p2 b)-the heat transfer to the air.
Answers: 1
image
Engineering, 04.07.2019 18:10, abdirahmansoloman
Air is to be cooled in the evaporator section of a refrigerator by passing it over a bank of 0.8-cm-outer-diameter and 0.4-m-long tubes inside which the refrigerant is evaporating at -20°c. air approaches the tube bank in the normal direction at 0°c and 1 atm with a mean velocity of 4 m/s. the tubes are arranged in-line with longitudinal and transverse pitches of sl- st 1.5 cm. there are 30 rows in the flow direction with 15 tubes in each row. determine (a) the refrigeration capacity of this system and (b) pressure drop across the tube bank. evaluate the air properties at an assumed mean temperature of -5°c and 1 atm. is this a good assumption?
Answers: 1
image
Engineering, 04.07.2019 18:10, lillygrl100
For the closed feedwater heater below, feedwater enters state 3 at a pressure of 2000 psia and temperature of 420 °f at a rate of ix10 ibhr. the feedwat extracted steam enters state 1 at a pressure of 1000 psia and enthalpy of 1500 btu/lbm. the extracted er leaves at an enthalpy of 528.7 btu/lbm steam leaves as a saturated liquid. (16) a) determine the mass flow rate of the extraction steam used to heat the feedwater (10) b) determine the terminal temperature difference of the closed feedwater heater
Answers: 3
image
Engineering, 04.07.2019 18:10, caitlynnpatton1208
Water in a partially filled large tank is to be supplied to the roof top, which is 8 m above the water level in the tank, through a 2.2-cm-internal-diameter pipe by maintaining a constant air pressure of 300 kpa (gage) in the tank. if the head loss in the piping is 2 m of water, determine the discharge rate of the supply of water to the roof top in liters per second.
Answers: 3
Do you know the correct answer?
Design and write an Octave function (you can specify any name) that performs the following functiona...

Questions in other subjects:

Konu
Health, 05.11.2020 02:00
Konu
Social Studies, 05.11.2020 02:00
Konu
Mathematics, 05.11.2020 02:00