![Engineering](/tpl/images/cats/User.png)
Engineering, 20.09.2020 14:01, Lucki1944
A cylinder with a 6.0 in. diameter and 12.0 in. length is put under a compres-sive load of 150 kips. The modulus of elasticity for this specimen is 8,000 ksiand Poissonās ratio is 0.35. Calculate the final length and the final diameter ofthis specimen under this load assuming that the material remains within thelinear elastic region.
![answer](/tpl/images/cats/otvet.png)
Answers: 3
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, bckyanne3
Afull journal bearing has a journal diameter of 27 mm, with a unilateral tolerance of -0.028 mm. the bushing bore has a diameter of 27.028 mm and a unilateral tolerance of 0.04 mm. the l/d ratio is 0.5. the load is 1.3 kn and the journal runs at 1200 rev/min. if the average viscosity is 50 mpa-s, find the minimum film thickness, the power loss, and the side flow for the minimum clearance assembly.
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, siri5645
At 12 noon, the count in a bacteria culture was 400; at 4: 00 pm the count was 1200 let p(t) denote the bacteria cou population growth law. find: (a) an expression for the bacteria count at any time t (b) the bacteria count at 10 am. (c) the time required for the bacteria count to reach 1800.
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, redrosesxx
Water at 55c flows across a flat plate whose surface temperature is held constant at 95c. if the temperature gradient at the plate's surface for a given value of x is 18 c/mm, find a) local heat transfer coefficient. b) heat flux
Answers: 3
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20, hayleymckee
Steam enters a converging nozzle at 3.0 mpa and 500Ā°c with a at 1.8 mpa. for a nozzle exit area of 32 cm2, determine the exit velocity, mass flow rate, and exit mach number if the nozzle: negligible velocity, and it exits (a) is isentropic (b) has an efficiency of 94 percent
Answers: 2
Do you know the correct answer?
A cylinder with a 6.0 in. diameter and 12.0 in. length is put under a compres-sive load of 150 kips....
Questions in other subjects:
![Konu](/tpl/images/cats/mat.png)
Mathematics, 12.05.2021 20:10
![Konu](/tpl/images/cats/mat.png)
Mathematics, 12.05.2021 20:10
![Konu](/tpl/images/cats/mat.png)
![Konu](/tpl/images/cats/fizika.png)
Physics, 12.05.2021 20:10
![Konu](/tpl/images/cats/ekonomika.png)
Business, 12.05.2021 20:10
![Konu](/tpl/images/cats/istoriya.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 12.05.2021 20:10
![Konu](/tpl/images/cats/istoriya.png)
![Konu](/tpl/images/cats/fizika.png)
![Konu](/tpl/images/cats/himiya.png)
Chemistry, 12.05.2021 20:10