![Engineering](/tpl/images/cats/User.png)
Engineering, 20.09.2020 09:01, indiii
1.5 m² module has an STC power rating of 225 W. Calculate the efficiency of the module as a percentage (don't include the percent sign in your answer though, just the number).
![answer](/tpl/images/cats/otvet.png)
Answers: 2
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, 0436500
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10, rayne40
A)-in the process of engineering design, explain the contribution of material selection. b)- explain the procedure of synthesis as is employed in engineering design. c)- is there any relationship between ergonomics and engineering design? explain. d)- safety consideration in engineering design includes human, product and the enviroment . explain how safety will be incorporated into the design?
Answers: 3
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20, mariahmimibrooks
Liquid flows at steady state at a rate of 2 lb/'s through a pump, which operates to raise the elevation of the liquid 100 ft from control volume inlet to exit. the liquid specific enthalpy at the inlet is 40.09 btu/lb and at the exit is 40.94 btub. the pump requires 3 btu/s of power to operate. if kinetic energy effects are negligible and gravitational acceleration is 32.174 tt/s, the heat transfer rate associated with this steady state process is most closely 1)-2,02 btu/s from the liquid to the surroundings 2)-3.98 btu/s from the surroundings to the liquid. 3)-4.96 btu/s from the surroundings to the liquid. 4)-1.04 btu/s from the liquid to the surroundings.
Answers: 2
![image](/tpl/images/cats/User.png)
Engineering, 05.07.2019 23:20, neisha2507
Which one of the following faults cause the coffee in a brewer to keep boiling after the brewing cycle is finished? a. an open circuit in the heating element b. a short circuit at the terminals c. welded contacts on the thermostat d. a leak around the gasket
Answers: 3
Do you know the correct answer?
1.5 m² module has an STC power rating of 225 W. Calculate the efficiency of the module as a percenta...
Questions in other subjects:
![Konu](/tpl/images/cats/istoriya.png)
![Konu](/tpl/images/cats/istoriya.png)
![Konu](/tpl/images/cats/obshestvoznanie.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 25.02.2021 21:00
![Konu](/tpl/images/cats/mat.png)
Mathematics, 25.02.2021 21:00
![Konu](/tpl/images/cats/biologiya.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 25.02.2021 21:00
![Konu](/tpl/images/cats/mat.png)
![Konu](/tpl/images/cats/mat.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 25.02.2021 21:00