Engineering
Engineering, 21.05.2020 04:00, kimberlylove387

1. Where are the output windings on an AC generator?
a. Stator
b. Rotor with commutator
c. Rotor with slip rings
d. None of the above

2. A generator rated for 30 KVA and power factor 0.8 has a maximum power output of:
a. 30 KW
b. 24 KW
c. 48 KW
d. None of the above

3. The voltage of an AC generator:
a. Rises to max in one direction and remains constant
b. Rises to max in one direction, falls to zero and rises in the same direction
c. Rises to max in one direction then fall to zero then rises to max in the opposite direction
d. None of the above

4. Power factor of a generator is:
a. Tan Ө
b. Cos Ө
c. Sin Ө
d. None

5. A generator supplied 150 V AC phase and load is 10 Ohms per phase. What is the phase current?
a. 25.5 A
b. 15 A
c. 1.5 A
d. None of the above

6. An AC generator’s frequency will:
a. Be proportional to the RPM at which it is driven
b. Always be constant regardless of the generators drive speed
c. Vary with changes in field strength.
d. None of the above

7. The sum of the instantaneous EMF’s in a three phase system is:
a. Three times the phase voltage
b. Zero
c. Equal to the line voltage
d. None of the above

8. The line voltage from a generator with a delta type connection will be:
a. Lower than the phase voltage
b. The same as the phase voltage
c. Higher than the phase voltage
d. None of the above
9. Permanent magnets in an AC generator are:
a. To provide initial excitation
b. To rectify the current
c. To control the frequency
d. None of the above

10. In delta-connected generator:
a. Line voltage = root 3 ties phase voltage, line current = phase current
b. Line voltage = phase voltage, line current = root 3 times phase current
c. Line voltage = phase voltage, line current =phase current divided by root 3
d. None of the above

answer
Answers: 1

Other questions on the subject: Engineering

image
Engineering, 04.07.2019 18:10, viicborella
Steel is coated with a thin layer of ceramic to protect against corrosion. what do you expect to happen to the coating when the temperature of the steel is increased significantly? explain.
Answers: 1
image
Engineering, 04.07.2019 18:10, keigleyhannah30
Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.
Answers: 3
image
Engineering, 04.07.2019 18:10, lerasteidl
Determine whether or not it is possible to compress air adiabatically from k to 140 kpa and 400 k. what is the entropy change during this process?
Answers: 3
image
Engineering, 04.07.2019 18:10, dval1146
You are making beer. the first step is filling the glass carboy with the liquid wort. the internal diameter of the carboy is 15 in., and you wish to fill it up to a depth of 2 ft. if your wort is drawn from the kettle using a siphon process that flows at 3 gpm, how long will it take to fill?
Answers: 1
Do you know the correct answer?
1. Where are the output windings on an AC generator?
a. Stator
b. Rotor with commutator<...

Questions in other subjects:

Konu
English, 27.03.2020 00:43
Konu
Mathematics, 27.03.2020 00:43
Konu
English, 27.03.2020 00:43