Engineering, 15.04.2020 03:03, torresq6647

A brass alloy is known to have a yield strength of 275 MPa (40,000 psi), a tensile strength of 380 MPa (55,000 psi), and an elastic modulus of 103 GPa (15.0×106 psi). A cylindrical specimen of this alloy 5.5 mm (0.22 in.) in diameter and 267 mm (10.52 in.) long is stressed in tension and found to elongate 7.0 mm (0.28 in.). On the basis of the information given, is it possible to compute the magnitude of the load that is necessary to produce this change in length? If not, explain why.

Answers: 1

Show answers

Answers

answered: renaudciera

Computation of the load is not possible because E(test) >E(yield)

Explanation:

We are asked to ascertain whether or not it is possible to compute, for brass, the magnitude of the load necessary to produce an elongation of 7.0 mm (0.28 in.). It is first necessary/ important to compute the strain at yielding from the yield strength and the elastic modulus, and then the strain experienced by the test specimen. Then, if

E(test) is less than E(yield), deformation is elastic and the load may be computed. However is E(test) is greater than E(yield) computation/determination of the load is not possible even though defamation is plastic and we have neither a stress-strain plot or a mathematical relating plastic stress and strain. Therefore, we can compute these two values as:

Calculation of E(test is as follows)

E(test) = change in l/lo= Elongation produced/stressed tension= 7.0mm/267mm

=0.0262

Computation of E(yield) is given below:

E(yield) = σy/E=275Mpa/103 ×10^6Mpa= 0.0027

Therefore, we won't be able to compute the load because for computation to take place, E(test) <E(yield). In this case, E(test) is greater than E(yield).

answered: kamraaa

It's not possible to compute the magnitude of the load

Explanation:

Given data:

Yield strength = 275Mpa

Tensile strength = 380Mpa

Elastic modulus = 103Gpa = 103 * 1000MPa

Diameter = 5.5 mm

Length = 267 mm

Elongation = 7.0 mm

Calculating the strain test value using the formula'

ε(test) = ΔL/Lo

Substituting, we have

ε = 7.0/267

= 0.0262

Calculating the yield strain using the formula

ε(yield) = бy/E

Substituting, we have

ε(yield) = 275/ 103 * 1000

= 275/103000

= 0.00267

From the calculation above, the strain test is greater than the yield. Therefore, it's not possible to compute the magnitude of the load.

ε(test) ⊃ ε(yield)

answered: Guest

In general, the greater the degree of undercooling of a liquid melt, the smaller the critical radius of the nuclei formed.

answered: Guest

answer:

the answer is d

explanation:

Other questions on the subject: Engineering

Engineering, 03.07.2019 15:10, margaret1758

If you were designing a bumper for a car, would you prefer it to exhibit elastic or plastic deformation? why? consider the functions of a bumper in both a minor "fender-bender" and a major collision.

Answers: 1

continue

Engineering, 04.07.2019 18:10, niyawilliams23

Asingle-geared blanking press has a stroke of 200 mm and a rated capacity of 320 kn. a cam driven ram is assumed to be capable of delivering the full press load at constant force during the last 15 percent of a constant-velocity stroke. the camshaft has an average speed of 90 rev/min and is geared to the flywheel shaft at a 6: 1 ratio. the total work done is to include an allowance of 16 percent for friction a) estimate the maximum energy fluctuation b) find the rim weight for an effective diameter of 1.2 m and a coefficient of speed fluctuation of 0.10

Answers: 1

continue

Engineering, 04.07.2019 18:10, oshawn108

Ahot wire operates at a temperature of 200°c while the air temperature is 20°c. the hot wire element is a tungsten wire of 5 um diameter and 2 mm in length. plot using excel current, heat transfer and heat generated by the wire for air velocity varying from 1-10 m/s in steps of lm/s? matlab the sensor voltage output, resistance, or assume nu 0.989 re033pr13 take air properties at tr (200°c20°c)/2 = 110°c properties of tungsten: c 0.13 kj/kg. k 3 p 19250 kg/m k (thermal conductivity) = 174 w/m. k

Answers: 2

continue

Engineering, 04.07.2019 18:20, alexis9263

Have a greater impact on maintenance productivity than any other support group. (clo5) a)-the top management b)-inventory and purchasing c)-sub-contracting d)-cmms

Answers: 2

continue

Do you know the correct answer?

A brass alloy is known to have a yield strength of 275 MPa (40,000 psi), a tensile strength of 380 M...