Engineering, 27.03.2020 00:03, autumnxng3094

G Problem 3 (Call by Value). The goal of this problem is to identify the redexes, if any, that can be reduced first in call by value evaluation stratgey for the given expressions. To identify a redex, you should highlight the ( x. t ) part of the redex in yellow and the t’ part of the redex in blue. Here is an example: Example. ( x. x x ) ( x. x x ) ( x. x x ) ( x. x x ) Answer. ( x. x x ) ( x. x x ) ( x. x x ) ( x. x x ) Note that you are only asked to identify the redexes and you are not asked to do the reduction. You are only asked to identify the redex and you are not asked to do the reduction. 1. ( x. x x ) x. x x 2. ( x. ( x. x ) x ) x 3. ( ( x. ( x. x ) x ) x. ( x. x ) x ) ( ( x. x ) x ) 4. ( ( x. ( x. x ) x ) x ( x. x ) x ) ( ( x. x ) x ) 5. x ( x. x ( x. x ) x ) (x. x ( x. x ) x ) x 6. x. x. x x. ( (x. x ) x ) x 7. ( ( x. y. ( y. x ) x. x x ) ) ( ( x. ( y. x ) ) x. x x ) 8. ( x. ( x. ( x. x ) x ) x ) ( ( x. x ) ( x. x ) ( x. x ) ) 9. x ( x. ( y. x ) x. x x ) ( x. ( y. x ) x. x x ) ( ( x. ( y. x ) ) x. x x ) 10. ( x. ( y. x ) x. x x ) ( ( x. ( y. x ) ) x. x x )

Answers: 2

Show answers

Other questions on the subject: Engineering

Engineering, 04.07.2019 18:10, niyawilliams23

Asingle-geared blanking press has a stroke of 200 mm and a rated capacity of 320 kn. a cam driven ram is assumed to be capable of delivering the full press load at constant force during the last 15 percent of a constant-velocity stroke. the camshaft has an average speed of 90 rev/min and is geared to the flywheel shaft at a 6: 1 ratio. the total work done is to include an allowance of 16 percent for friction a) estimate the maximum energy fluctuation b) find the rim weight for an effective diameter of 1.2 m and a coefficient of speed fluctuation of 0.10

Answers: 1

continue

Engineering, 04.07.2019 18:20, krojas015

Asolid cylinder is concentric with a straight pipe. the cylinder is 0.5 m long and has an outside diameter of 8 cm. the pipe has an inside diameter of 8.5 cm. the annulus between the cylinder ad the pipe contains stationary oil. the oil has a specific gravity of 0.92 and a kinematic viscosity of 5.57 x 10-4 m2/s. most nearly, what is the force needed to move the cylinder along the pipe at a constant velocity of 1 m/s?

Answers: 3

continue

Engineering, 04.07.2019 18:20, yasyyas646646

Agas mixture consists of 8 kmol of h2 and 2 kmol of n2. determine the mass of each gas and the apparent gas constant of the mixture.

Answers: 3

continue

Engineering, 04.07.2019 18:20, rjone8429

Asimple rankine cycle uses water as the working fluid. the water enters the turbine at 10 mpa and 480c while the condenser operates at 6 kpa. if the turbine has an isentropic efficiency of 80 percent while the pump has an isentropic efficiency of 70 percent determine the thermal efficiency

Answers: 1

continue

Do you know the correct answer?

G Problem 3 (Call by Value). The goal of this problem is to identify the redexes, if any, that can b...