Engineering
Engineering, 25.03.2020 23:34, ramentome7542

Ayudenme!!
Cuál de las siguientes afirmaciones es verdadera: (V o F)

- El EPP será de material adecuado y tendrá el grado de protección necesario
- El trabajador no podrá utilizar más de un EPP a la vez, es incompatible.
- Una de las grandes ventajas del EPP es que se puede utilizar toda la vida, ya que no tienen fecha de caducidad.

Los Equipos de Protección Personal (EPP): (V o F)

- No están regulados por ninguna normativa.
- Pueden proteger a una parte concreta del cuerpo o garantizar una protección total.
- Es fundamental que estén bien diseñados, ya que esta característica es suficiente para garantizar que se pueden utilizar sin necesidad de informar al trabajador previamente.
- El EPP ofrece poca o ninguna protección si no se usa correctamente.

¿Cuál de las siguientes es una razón válida para no usar el EPP cuando
es requerido?

a. Usted está ocupado
b. Solo está haciendo un trabajo rápido
c. Es incómodo
d. Ninguna de las opciones anteriores

¿Cuál es el propósito de un casco?

a. Protegerlo de objetos que caen
b. Protegerlo de peligros por encima de su cabeza
c. La protección del oír
d. A y B

¿Cuál de las siguientes puede causar una lesión severa a los ojos si no
se usa la protección ocular adecuada?
a. Las partículas metálicas aéreas
b. Los clavos o puntillas
c. Los Químicos
d. Todas las opciones anteriores

¿Con qué frecuencia debe usted inspeccionar su EPP para cerciorar que
está en buena condición y funcionamiento?

a. Antes de cada uso
b. Una vez por semana
c. Una vez por mes
d. Cuando sea necesario

answer
Answers: 2

Other questions on the subject: Engineering

image
Engineering, 04.07.2019 18:10, keigleyhannah30
Aplate clutch has a single pair of mating friction surfaces 250-mm od by 175-mm id. the mean value of the coefficient of friction is 0.30, and the actuating force is 4 kn. a) find the maximum pressure and the torque capacity using the uniform-wear model. b) find the maximum pressure and the torque capacity using the uniform-pressure model.
Answers: 3
image
Engineering, 04.07.2019 18:10, caitlynnpatton1208
Water in a partially filled large tank is to be supplied to the roof top, which is 8 m above the water level in the tank, through a 2.2-cm-internal-diameter pipe by maintaining a constant air pressure of 300 kpa (gage) in the tank. if the head loss in the piping is 2 m of water, determine the discharge rate of the supply of water to the roof top in liters per second.
Answers: 3
image
Engineering, 04.07.2019 18:20, kendrawalraven
The characteristic roots of a dynamic system are: 1.7920 1.8160 i, -1.7920 1.8160 i, -0.4160 what is the order of this system? what are the settling time and damping ratio of the system?
Answers: 3
image
Engineering, 04.07.2019 19:10, nida7864
An engine, weighing 3000 n, is supported on a pedestal mount. it has been observed that the engine induces vibration into the surrounding area through its pedestal at the maximum operating speed. determine the stiffness of the dynamic vibration absorber spring in (n/m) that will reduce the vibration when mounted on the pedestal. the magnitude of the exciting force is 250 n, and the amplitude of motion of the auxiliary mass is to be limited to 2 mm note: in this question type-in right numbers, no decimals, no fractions, no unit. approximate to right number if needed
Answers: 3
Do you know the correct answer?
Ayudenme!!
Cuál de las siguientes afirmaciones es verdadera: (V o F)

- El EPP será...

Questions in other subjects:

Konu
History, 04.02.2020 16:50