Engineering, 24.03.2020 18:01, texassaint797
Liquid flows at steady state at a rate of 2 lb/s through a pump, which operates to raise the elevation of the liquid 100 ft from control volume inlet to exit. The liquid specific enthalpy at the inlet is 40.09 Btu/lb and at the exit is 40.94 Btu/lb. The pump requires 3 Btu/s of power to operate. If kinetic energy effects are negligible and gravitational acceleration is 32.174 ft/s2, the heat transfer rate associated with this steady state process is most closely:
A) 2.02 Btu/s from the liquid to the surroundings.
B) 3.98 Btu/s from the surroundings to the liquid.
C) 4.96 Btu/s from the surroundings to the liquid.
D) 1.04 Btu/s from the liquid to the surroundings.
Answers: 2
Btu/lb)
Btu/lb)
)
)
= 3 Btu/s![Q_{cv}-W{cv}+m[(h_1-h_2)+(\frac{V_1^2-V_2^2}{2})+g(z_1-z_2)]=0](/tpl/images/0561/0359/16e63.png)
![Q_{cv}-W{cv}+m[(h_1-h_2)+g(z_1-z_2)]=0](/tpl/images/0561/0359/3924d.png)
![Q_{cv}-(-3)+2[(40.09-40.94)+\frac{32.174(0-100)}{778*32.174} ]=0\\Q_{cv}+3+2[-0.85-0.1285 ]=0\\Q_{cv}+3+2(-0.9785)=0\\Q_{cv}+3-1.957=0\\Q_{cv}+1.04=0\\Q_{cv}=-1.04\\](/tpl/images/0561/0359/ef0f5.png)
Other questions on the subject: Engineering
Engineering, 04.07.2019 18:10, jadeochoa4466
The temperature of air decreases as it is compressed by an adiabatic compressor. a)- true b)- false
Answers: 2
Engineering, 04.07.2019 18:10, meganwintergirl
Afour cylinder four-stroke in-line engine has a stroke of 160mm, connecting rod length of 150mm, a reciprocating mass of 3kg and its firing order is 1-3-4-2. the spacing between cylinders is 100mm. i. show that the engine is in balance with regard to the primary inertia forces and primary 3. a and secondary inertia couples. li determine the out of balance secondary inertia force ii. propose ways of balancing this out of balance force and discuss the challenges that will arise
Answers: 3
Engineering, 04.07.2019 18:10, DestyHilBan1183
Adouble-strand no. 60 roller chain is used to transmit power between a 13-tooth driving sprocket rotating at 300 rev/min and a 52-tooth driven sprocket. a) what is the allowable horsepower of this drive? b) estimate the center-to-center distance if the chain length is 82 pitches. c) estimate the torque and bending force on the driving shaft by the chain if the actual horsepower transmitted is 30 percent less than the corrected (allowable) power.
Answers: 3
Engineering, 04.07.2019 18:10, samanthabutryn
Which one from below is not one of the reasons of planning failures? (clo3) a)-planner is careless. b-planner spend less time in the field but more time on the desk c)-planner is not qualified d)-planner does not have sufficient time to properly plan
Answers: 3
Do you know the correct answer?
Liquid flows at steady state at a rate of 2 lb/s through a pump, which operates to raise the elevati...
Questions in other subjects:
French, 20.05.2020 03:57
Biology, 20.05.2020 03:57
Mathematics, 20.05.2020 03:57
Chemistry, 20.05.2020 03:57
History, 20.05.2020 03:57
Mathematics, 20.05.2020 03:57
