Engineering, 03.03.2020 20:03, Serenitybella

Plot the following trig functions using subplots, choosing an appropriate layout for the number of functions displayed. The subplots should include a title which is the equation displayed. The independent variable (angle) should vary from 0 to 360 degrees and the plots should use a solid red line.

Answers: 3

Show answers

Answers

answered: dannyhouseman55

The question is incomplete! The complete question along with Matlab code and explanation is provided below.

Question

Plot the following trig functions using subplots, choosing an appropriate layout for the number of functions displayed. The subplots should include a title which is the equation displayed. The independent variable (angle) should vary from 0 to 360 degrees and the plots should use a solid red line.

1. cos(u - 45)

2. 3cos(2u) - 2

3. sin(3u)

4. -2cos(u)

Matlab Code with Explanation:

u=[0:0.01:2*pi] % independent variable represents 0 to 360 degrees in steps of 0.01

y1=cos(2*pi*u-45); % function 1

y2=3*cos(2*pi*2*u)-2; % function 2

y3=sin(2*pi*3*u); % function 3

y4=-2*cos(2*pi*u); % function 4

subplot(4,1,1) % 4 rows, 1 column and at position 1

plot(u,y1,'r'); % this function plots y w.r.t u and 'r' is for red color

grid on % turns on grids

xlabel('u') % label of x-axis

ylabel('y1') % label of x-axis

title('y1=cos(2*pi*u-45)') % title of the plot

ylim([-3 3]) % limits of y-axis

xlim([0 2*pi]) % limits of x-axis

% repeat the same procedure for the remaining 3 functions

subplot(4,1,2)

plot(u,y2,'r');

grid on

xlabel('u')

ylabel('y2')

title('y2=3*cos(2*pi*2*u)-2')

ylim([-6 3])

xlim([0 2*pi])

subplot(4,1,3)

plot(u,y3,'r');

grid on

xlabel('u')

ylabel('y3')

title('y3=sin(2*pi*3*u)')

ylim([-3 3])

xlim([0 2*pi])

subplot(4,1,4)

plot(u,y4,'r');

grid on

xlabel('u')

ylabel('y4')

title('y4=-2*cos(2*pi*u)')

ylim([-3 3])

xlim([0 2*pi])

Output Results:

The first plot shows a cosine wave with a phase shift of 45°

The second plot shows that the amplitude of the cosine wave is increased and the wave is shifted below zero level into the negative y-axis because of -2 also there is a increase in frequency since it is multiplied by 2.

The third plot shows that the frequency of the sine wave is increased since it is multiplied by 3.

The fourth plot shows a cosine wave which is multiplied by -2 and starts from the negative y-axis.

Plot the following trig functions using subplots, choosing an appropriate layout for the number of f

answered: Guest

answer: jesus loves you

explanation:

answered: Guest

Where is the rest of the information?

Other questions on the subject: Engineering

Engineering, 03.07.2019 15:10, theamandawhite

Ahouse has the following electrical appliance usage (1) single 40w lamp used for 4 hours per day (2) single 60w fan used for 12 hours per day (3) single 200w refrigerator that runs 24 hours per day with compressor run 12 hours and off 12 hours find the solar power inverter size in watt with correction factor of 1.25.

Answers: 1

continue

Engineering, 04.07.2019 18:10, koolgurl2003

Apump is used to circulate hot water in a home heating system. water enters the well-insulated pump operating at steady state at a rate of 0.42 gal/min. the inlet pressure and temperature are 14.7 lbf/in.2, and 180°f, respectively; at the exit the pressure is 60 lbf/in.2 the pump requires 1/15 hp of power input. water can be modeled as an incompressible substance with constant density of 60.58 lb/ft3 and constant specific heat of 1 btu/lb or. neglecting kinetic and potential energy effects, determine the temperature change, in °r, as the water flows through the pump.

Answers: 1

continue

Engineering, 04.07.2019 18:10, anna22684

Water at 70°f and streams enter the mixing chamber at the same mass flow rate, determine the temperature and the quality of the exiting stream. 0 psia is heated in a chamber by mixing it with saturated water vapor at 20 psia. if both streams enters the mixing chamber at the same mass flow rate, determine the temperature and the quality of the existing system.

Answers: 2

continue

Engineering, 04.07.2019 18:10, johnthienann58

Thermal stresses are developed in a metal when its a) initial temperature is changed b) final temperature is changed c) density is changed d) thermal deformation is prevented e) expansion is prevented f) contraction is prevented

Answers: 2

continue

Do you know the correct answer?

Plot the following trig functions using subplots, choosing an appropriate layout for the number of f...