Engineering
Engineering, 25.02.2020 23:18, mvasquez3122p4vahv

A Dual cycle engine is analyzed using the cold air standard method. Given the conditions at state 1, compression ratio (r), and cutoff ratio (rc) determine the efficiency and other values listed below.
Note: The specific heat ratio and gas constant for air are given as k=1.4 and R=0.287 kJ/kg-K respectively.

--Given Values--
T1 (K) = 328
P1 (kPa) = 190
r = 14
rp = 1.3
rc = 1.3

a) Determine the specific internal energy (kJ/kg) at state 1.
b) Determine the temperature (K) at state 2.
c) Determine the pressure (kPa) at state 2.
d) Determine the specific internal energy (kJ/kg) at state 2.
e) Determine the temperature (K) at state 3.
f) Determine the pressure (kPa) at state 3.
g) Determine the specific internal energy (kJ/kg) at state 3.
h) Determine the specific enthalpy (kJ/kg) at state 3.
i) Determine the temperature (K) at state 4.
j) Determine the pressure (kPa) at state 4.
k) Determine the specific enthalpy (kJ/kg) at state 4.

l) Determine the temperature (K) at state 5.

m) Determine the pressure (kPa) at state 5.

n) Determine the specific internal energy (kJ/kg) at state 5.

o) Determine the net work per cycle (kJ/kg) of the engine.

p) Determine the heat addition per cycle (kJ/kg) of the engine.

q) Determine the efficiency (%) of the engine.

answer
Answers: 2

Other questions on the subject: Engineering

image
Engineering, 03.07.2019 15:10, breannaasmith1122
Two flowing streams of argon gas are adiabatically mixed to form a single flow/stream. one stream is 1.5 kg/s at 400 kpa and 200 c while the second stream is 2kg/s at 500 kpa and 100 ? . it is stated that the exit state of the mixed single flow of argon gas is 150 c and 300 kpa. assuming there is no work output or input during the mixing process, does this process violate either the first or the second law or both? explain and state all your assumptions.
Answers: 1
image
Engineering, 04.07.2019 18:10, Candi9697
A-mn has a cubic structure with a0 0.8931 nm and a density of 7.47 g/cm3. b-mn has a different cubic structure, with a0 0.6326 nm and a density of 7.26 g/cm3. the atomic weight of manganese is 54.938 g/mol and the atomic radius is 0.112 nm. determine the percent volume change that would occur if a-mn transforms to b-mn.
Answers: 2
image
Engineering, 04.07.2019 18:10, QueenLife4869
Awall of 0.5m thickness is to be constructed from a material which has average thermal conductivity of 1.4 w/mk. the wall is to be insulated with a material having an average thermal conductivity of 0.35 w/mk so that heat loss per square meter shall not exceed 1450 w. assume inner wall surface temperature of 1200°c and outer surface temperature of the insulation to be 15°c. calculate the thickness of insulation required.
Answers: 3
image
Engineering, 04.07.2019 18:20, luisgonz5050
Find the kinematic pressure of 160kpa. for air, r-287 j/ kg k. and hair al viscosity of air at a temperature of 50°c and an absolute (10 points) (b) find the dynamic viscosity of air at 110 °c. sutherland constant for air is 111k
Answers: 3
Do you know the correct answer?
A Dual cycle engine is analyzed using the cold air standard method. Given the conditions at state 1,...

Questions in other subjects:

Konu
Mathematics, 11.06.2021 07:40
Konu
Mathematics, 11.06.2021 07:40
Konu
Social Studies, 11.06.2021 07:40