![Engineering](/tpl/images/cats/User.png)
Engineering, 03.12.2019 18:31, sabrinabowers4308
To calculate the normal and shear stresses at a point in a beam subjected to a combined loading. the state of stress at a point is a description of the normal and shear stresses at that point. when a structural element is subjected to multiple kinds of loads, the effects of each can be combined using the principle of superposition, as long as the deflections remain small, the response is elastic, and the material is homogenous. the beam shown (figure 1) is supported by a pin at a and a cable at b. two loads p = 20 kn are applied straight down from the centerline of the bottom face. determine the state of stress at the point shown (figure 2) in a section 2 m from the wall. the dimensions are w = 4.6 cm , h = 11.5 cm , l = 0.8 m , a = 1.5 cm , and b = 4 cm .
![answer](/tpl/images/cats/otvet.png)
Answers: 1
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
Engineering, 03.07.2019 14:10, volleyballfun24
If the thermal strain developed in polyimide film during deposition is given as 0.0044. assume room temperature is kept at 17.3 c, and thermal coefficient of expansion for the film and the substrate are 54 x 10^-6c^-1 and 3.3 x 10^-6c^-1respectively. calculate the deposition temperature.
Answers: 3
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, ahmedeldyame
Aloaded platform of total mass 500 kg is supported by a dashpot and by a set of springs of effective stiffness 72 kn/m. it is observed that when the platform is depressed through a distance x = 12.5 cm below its equilibrium position and then released without any initial velocity; it reaches its equilibrium position in the shortest possible time without overshoot. find the position and velocity of the loaded platform 0.10 sec. after its release. if a further load of 400 kg is added to the platform, find, i) the frequency of damped vibrations, and i) the amplitude of vibration after 2 complete oscillations, given that the initial amplitude is 15 cm.
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20, hayleymckee
Steam enters a converging nozzle at 3.0 mpa and 500Β°c with a at 1.8 mpa. for a nozzle exit area of 32 cm2, determine the exit velocity, mass flow rate, and exit mach number if the nozzle: negligible velocity, and it exits (a) is isentropic (b) has an efficiency of 94 percent
Answers: 2
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:10, pjgolden04
How to increase the thermal officiency of an ideal simple rankino cycle? among these methods, which one is the best and why?
Answers: 2
Do you know the correct answer?
To calculate the normal and shear stresses at a point in a beam subjected to a combined loading. the...
Questions in other subjects:
![Konu](/tpl/images/cats/geografiya.png)
Geography, 18.07.2019 08:30
![Konu](/tpl/images/cats/biologiya.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 18.07.2019 08:30
![Konu](/tpl/images/cats/en.png)
![Konu](/tpl/images/cats/istoriya.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 18.07.2019 08:30
![Konu](/tpl/images/cats/en.png)
![Konu](/tpl/images/cats/mat.png)
Mathematics, 18.07.2019 08:30
![Konu](/tpl/images/cats/en.png)