![Engineering](/tpl/images/cats/User.png)
Engineering, 13.09.2019 23:30, smiley0326
Phase difference measurement is possible using: select one: 1. accelerometers 2. data collectors 3. dual channel analysers 4. velocity pickups 5. light sensors
![answer](/tpl/images/cats/otvet.png)
Answers: 1
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, 0436500
Aturning operation is performed with following conditions: rake angle of 12°, a feed of 0.35 mm/rev, and a depth of cut of 1.1 mm. the work piece is aluminum alloy 6061 with t6 heat treatment (a16061-t6). the resultant chip thickness was measured to be 1.0 mm. estimate the cutting force, fc. use shear stress of 207 mpa and coefficient of friction on the tool face of 0.6.
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20, alexis9263
Have a greater impact on maintenance productivity than any other support group. (clo5) a)-the top management b)-inventory and purchasing c)-sub-contracting d)-cmms
Answers: 2
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20, rjone8429
Asimple rankine cycle uses water as the working fluid. the water enters the turbine at 10 mpa and 480c while the condenser operates at 6 kpa. if the turbine has an isentropic efficiency of 80 percent while the pump has an isentropic efficiency of 70 percent determine the thermal efficiency
Answers: 1
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20, Katmcfee7681
Acommercial grade cubical freezer, 4 m on a side, has a composite wall consisting of an exterior sheet of 5.0-mm thick plain carbon steel (kst= 60.5 w/m k), an intermediate layer of 100-mm thick polyurethane insulation (kins 0.02 w/m k), and an inner sheet of 5.0- mm thick aluminium alloy (kal polyurethane insulation and both metallic sheets are each characterized by a thermal contact resistance of r 2.5 x 104 m2 k/w. (a) what is the steady-state cooling load that must be maintained by the refrigerator under conditions for which the outer and inner surface temperatures are 25°c and -5°c, respectively? (b) for power saving purpose, which wall material should be increased/reduced in. thickness in order to reduce 50% of the cooling load found in part (a)? redesign the thickness of the proposed material. 177 w/m-k). adhesive interfaces between the q=575.93 w
Answers: 2
Do you know the correct answer?
Phase difference measurement is possible using: select one: 1. accelerometers 2. data collectors 3...
Questions in other subjects:
![Konu](/tpl/images/cats/himiya.png)
Chemistry, 01.03.2021 20:30
![Konu](/tpl/images/cats/mat.png)
Mathematics, 01.03.2021 20:30
![Konu](/tpl/images/cats/fizika.png)
![Konu](/tpl/images/cats/biologiya.png)
![Konu](/tpl/images/cats/istoriya.png)
![Konu](/tpl/images/cats/mat.png)
![Konu](/tpl/images/cats/obshestvoznanie.png)
Social Studies, 01.03.2021 20:30
![Konu](/tpl/images/cats/mat.png)
Mathematics, 01.03.2021 20:30
![Konu](/tpl/images/cats/mat.png)
Mathematics, 01.03.2021 20:30