![Engineering](/tpl/images/cats/User.png)
Engineering, 23.08.2019 01:30, ehklu1226
Describe the key components of a servo motor? how is continuous motion servo different than standard servo?
![answer](/tpl/images/cats/otvet.png)
Answers: 3
Other questions on the subject: Engineering
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:10, caitlynnpatton1208
Water in a partially filled large tank is to be supplied to the roof top, which is 8 m above the water level in the tank, through a 2.2-cm-internal-diameter pipe by maintaining a constant air pressure of 300 kpa (gage) in the tank. if the head loss in the piping is 2 m of water, determine the discharge rate of the supply of water to the roof top in liters per second.
Answers: 3
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 18:20, kodyclancy
Aquick transition of the operating speed of a shaft from its critical speed will whirl amplitude. (a) increase (b) limit (c) not affect (d) zero
Answers: 2
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20, Katmcfee7681
Acommercial grade cubical freezer, 4 m on a side, has a composite wall consisting of an exterior sheet of 5.0-mm thick plain carbon steel (kst= 60.5 w/m k), an intermediate layer of 100-mm thick polyurethane insulation (kins 0.02 w/m k), and an inner sheet of 5.0- mm thick aluminium alloy (kal polyurethane insulation and both metallic sheets are each characterized by a thermal contact resistance of r 2.5 x 104 m2 k/w. (a) what is the steady-state cooling load that must be maintained by the refrigerator under conditions for which the outer and inner surface temperatures are 25°c and -5°c, respectively? (b) for power saving purpose, which wall material should be increased/reduced in. thickness in order to reduce 50% of the cooling load found in part (a)? redesign the thickness of the proposed material. 177 w/m-k). adhesive interfaces between the q=575.93 w
Answers: 2
![image](/tpl/images/cats/User.png)
Engineering, 04.07.2019 19:20, natalie2sheffield
Acompressor compresses a gas, a pump compresses a liquid. for a given pressure ratio, why does it take more work to compress a gas in a compressor than a liquid in a pump? a)- for a given pressure ratio the average specific volume for a gas is much higher than the average specific volume for a liquid. b)- there is no difference. the only difference is the amount of heat generated (not work) c)- for a given pressure ratio the average volurge for a gas is much higher than the average volume for a liquid. d)-there is no difference
Answers: 3
Do you know the correct answer?
Describe the key components of a servo motor? how is continuous motion servo different than standar...
Questions in other subjects:
![Konu](/tpl/images/cats/ekonomika.png)
![Konu](/tpl/images/cats/fizika.png)
![Konu](/tpl/images/cats/User.png)
![Konu](/tpl/images/cats/ekonomika.png)
![Konu](/tpl/images/cats/biologiya.png)
Biology, 27.02.2020 02:30
![Konu](/tpl/images/cats/ekonomika.png)
![Konu](/tpl/images/cats/mat.png)
![Konu](/tpl/images/cats/ekonomika.png)
![Konu](/tpl/images/cats/User.png)
![Konu](/tpl/images/cats/biologiya.png)
Biology, 27.02.2020 02:30