Engineering

Engineering, 26.07.2019 17:10, sarah7484

Ametal column of external diameter 300 mm and thickness 20 mm carries a load of 400 kn at an eccentricity of 50 mm. determine the maximum and minimum stresses in the column if its length is 5 m, and both ends of the column are fixed. e 95 gpa.

answer

Answers: 1

Show answers

Similar questions

Предмет

Engineering, 11.07.2019 03:30, tylersabin72

Apressure cylinder has an outer diameter 200 mm, maximum external pressure 4 mpa, and maximum allowable shear stress 27.5 mpa. determine the appropriate value of the minimum wall thickness the appropriate value of the minimum wall thickness

Answers: 1

Предмет

Engineering, 17.07.2019 21:10, garacey241

Ahollow circular column of external diameter 200 mm and thickness 5 mm is 6 m long. for the material properties of the column, a column is considered short if the slenderness ratio is less than or equal to 70 a yield stress of 280 mpa to a proportional limit of 210 mpa may be used. find the load capacity of the column.

Answers: 2

Предмет

Engineering, 18.09.2019 05:00, zanaplen27

Asteel column with 4-in diameter supports a compressive load of 160-kips. the column rests on a 10-in by 10-in base plate with 1-in thickness, which in turn rest on a square 40-in by 40-in concrete slab with 6-in thickness. if (taiiow and tatiow in the steel are not to exceed 18-ksi and 9-ksi and in the concrete are not to exceed 3,000-psi and 1,200-psi respectively, and bearing stress on the soil be limited to 300-psi, determine whether all the dimensions given for the column, the base plate, and the concrete are adequate or not? 160-kips answers: all adequate, except plate thickness: minimum thickness t = 1.27-in

Answers: 1

Предмет

Physics, 11.10.2019 08:20, mia3128

Arod loaded in tension with an axial force of p- 1200 n and circular cross-sectional area of a undergoes a nominal stress ofo p/a pia. 1(a)-using a design factor of 3.0 and a material strength of 120 kpa, determine the minimum diameter of a solid circular rod. 1b)-using a proper table, select a preferred diameter and determine the rod's factor of safety 1(c) -the following variations are assumed: the rod's diameter is manufactured within ± 3% ofits nominal dimension, the load is known within± 4% ofthe nominal load, and the material strength is known within 6% of the nominal strength value. if the designer is using nominal values and a stress equation, determine what design factor should be used so that the stress does not exceed the strength. the load application would be considered dynamic (a sudden increase from a zero value) while eccentricity is not considered here. note: the positive and negative values are the maximum and minimum values allowed in the manufacturing, respectively

Answers: 1

Do you know the correct answer?

Ametal column of external diameter 300 mm and thickness 20 mm carries a load of 400 kn at an eccentr...

Questions in other subjects:

Konu

Business, 08.10.2021 17:00

explain the argument that if products improve in quality but the bls ignores the quality improvements, then the cpi will overstate the rate of increase in the cost of living....

Konu

Computers and Technology, 08.10.2021 17:00

Which factor is critical to the successful implementation of IS? A. isolating users from the IS system B. effective planning by top management c. isolating processes...

Konu

Social Studies, 08.10.2021 17:00

According to American Sociologist C. Wright Mills, people look for relationships between their personal lives and their society. Using the concept of sociological imagination, desc...

Konu

Biology, 08.10.2021 17:00

what are some other organisms that you’ve encountered that interact with people in both urban and rural environments, that you’ve seen these three types of variations between indiv...

Konu

Mathematics, 08.10.2021 17:00

What is the slope of a triangle with the run of 1 and the rise of 4...

Konu

Mathematics, 08.10.2021 17:00

A rectangular room is 15 feet long and 12 feet wide. Find the perimeter and the area of the room....

Konu

Chemistry, 08.10.2021 17:00

five ml of ethanol has a mass of 3.9 G, and 5.0 mL of benzene has a mass of 4.4 G which liquid is denser...

Konu

Biology, 08.10.2021 17:00

Question 1(Multiple Choice Worth 2 points)(05.05 MC)How does the human immune system initially respond to a pathogen?...

Konu

Mathematics, 08.10.2021 17:00

The coordinates of point J are (-7, 2), and the midpoint of JK is at L (3, 5). What are the coordinates of point K?...

Konu

English, 08.10.2021 17:00

Pls Help Me with this answer ...

Other tasks in the category: Engineering More task