Engineering

Engineering, 11.07.2019 03:30, jorden73

Which is true of drawing? 1999 a)-cast iron is a common die material b)-there is a limit to the wire diameter reduction in one pass c)-the applied load is greater than the fs d)-the material is pushed through the die

answer

Answers: 3

Show answers

Similar questions

Предмет

Physics, 23.06.2019 03:00, cody665

Aforce of 40n applied at the end of length 4m and diameter 2.00mm process and extension of 0.24mm,calculate the stress on the wire, strain in the wire and the young modulus for the material of the wire

Answers: 1

Предмет

Engineering, 20.08.2019 17:20, Ron1213

A150mm diameter steel shaft is to have a press-fit with a 300mm outer diameter by 250mm long hub of cast iron. the maximum tangential stress is to 35mpa. the coefficient of friction for both cast iron and steel is to be 0.3 and modulus of elasticity of the cast iron is to be 100gpa and steel is to be 200gpa. determine the following: i) the interference ii) the axial force for the system iii) the torque transmitted by the system

Answers: 2

Предмет

Engineering, 13.11.2019 01:31, Annabeans1105

Consider a cylindrical rod stock fabricated from a material with a stress strain relationship as follows: σ =5000 + 2000 ε < (where o is in psi) and can be note: since this constitutive law was obtained from uniaxial tension tests, σ and εreplaced by effective stress and effective strain. a. if the original diameter of the rod is 0.2 in, what is the minimum possible diameter that can be drawn in the first pass? assume that there is no redundant work and that the frictional work is 25% of the ideal work of deformation. b. what is the drawing force required to complete this operation? c. if the drawing equipment limit is 2000 lbs, is the equipment capable to perform this operation? if not, given the force available (2000 lbs), what is the corresponding exit diameter at the first pass?

Answers: 2

Предмет

Physics, 26.11.2019 06:31, jenna34032

Acopper wire and an iron wire of equal length l and diameter d are joined, and a potential difference v is applied between the ends of the composite wire. calculate the potential difference (in volts) across the iron wire. assume that l = 2.97 m, d = 0.88 mm, and v = 157 v.

Answers: 1

Do you know the correct answer?

Which is true of drawing? 1999 a)-cast iron is a common die material b)-there is a limit to the wir...

Questions in other subjects:

Konu

Geography, 13.11.2020 19:20

More than half of brachiopod species became extinct at the end of the...

Konu

Arts, 13.11.2020 19:20

In art , the term Value refers to a. the color b. the lightness or darkness of a color or tone , ranging from black to white c. the hue d. t...

Konu

Health, 13.11.2020 19:20

What type of drug is heroin?...

Konu

English, 13.11.2020 19:20

On this day in 1815, Women’s Rights Leader Elizabeth Cady Stanton was born. Stanton is well known for her work in women’s rights. Why do you think women were not allowed to vote fo...

Konu

History, 13.11.2020 19:20

During this process, clauses are added and removed from a bill. a. Re-election b. Voting c. Deliberation...

Konu

Arts, 13.11.2020 19:20

Which is a marketing influence on consumer demand? А. communication B. advertising c. recession D. transportationRes...

Konu

Mathematics, 13.11.2020 19:20

What is the value of ? pls help ...

Konu

Mathematics, 13.11.2020 19:20

Help me! explain how to use friendly percents to find 35% of 80...

Konu

History, 13.11.2020 19:20

Why did the Spanish American War impact the United States as an Imperial Power?...

Konu

Mathematics, 13.11.2020 19:20

100 POINTS i will give brainliest HELP ME !!...

Other tasks in the category: Engineering More task