Computers and Technology

One of the main differences between ISO on a DSLR and ISO on a film camera is . On a film camera, ISO could be change on a shot-by-shot basis.
Higher ISOs on DSLRs reduce the amount of noise in an image.
On a film camera, ISO had to be the same for every photo on the roll of film.
None of the above

answer
Answers: 1

Other questions on the subject: Computers and Technology

image
Computers and Technology, 21.06.2019 21:00, calmicaela12s
The mode is generally used when delivering a presentation to an need now
Answers: 1
image
Computers and Technology, 23.06.2019 00:10, makailaaa2
My has been slow anyone else’s ?
Answers: 1
image
Computers and Technology, 23.06.2019 19:00, amayax77
Write a program that displays the following menu: geometry calculator 1. calculate the area of a circle 2. calculate the area of a rectangle 3. calculate the area of a triangle 4. quit enter your choice (1-4): if the user enters 1, the program should ask for the radius of the circle and then display its area. use the following formula: area = ď€(the square of r) use 3.14159 for ď€ and the radius of the circle for r. if the user enters 2, the program should ask for the length and width of the rectangle and then display the rectangle’s area. use the following formula: area = length * width if the user enters 3, the program should ask for the length of the triangle’s base and its height, and then display its area. use the following formula: area = base * height * .5 if the user enters 4, the program should end. input validation: display an error message if the user enters a number outside the range of 1 through 4 when selecting an item from the menu. do not accept negative values for the circle’s radius, the rectangle’s length or width, or the triangle’s base or height. note: if the user enters an improper menu choice (1-4), the program prints "the valid choices are 1 through 4. run the program again and select one of those." if the user enters a negative radius, the program prints "the radius can not be less than zero." if the user enters a negative value for height or base, the program prints "only enter positive values for base and height."
Answers: 1
image
Computers and Technology, 23.06.2019 19:00, Heyitsbrandi
Now you’re on your own. include a short summary of this section with plots in your lab report. write a matlab script file to do steps (a) through (d) below. include a listing of the script file with your report. 1 the soundsc(xx, fs) function requires two arguments: the first one (xx) contains the vector of data to be played, the second argument (fs) is the sampling rate for playing the samples. in addition, soundsc(xx, fs) does automatic scaling and then calls sound(xx, fs) to actually play the signal. mcclellan, schafer, and yoder, dsp first, 2e, isbn 0-13-065562-7. prentice hall, upper saddle river, nj 07458. c 2015 pearson education, inc. 4 mcclellan, schafer and yoder, signal processing first. prentice hall, upper saddle river, new jersey, 2003. c 2003 prentice hall. (a) generate a time vector (tt) to cover a range of t that will exhibit approximately two cycles of the 4000 hz sinusoids defined in the next part, part (b). use a definition for tt similar to part 2.2(d). if we use t to denote the period of the sinusoids, define the starting time of the vector tt to be equal to t , and the ending time as ct . then the two cycles will include t d 0. finally, make sure that you have at least 25 samples per period of the sinusoidal wave. in other words, when you use the colon operator to define the time vector, make the increment small enough to generate 25 samples per period. (b) generate two 4000 hz sinusoids with arbitrary amplitude and time-shift. x1.t / d a1 cos.2
Answers: 1
Do you know the correct answer?
One of the main differences between ISO on a DSLR and ISO on a film camera is . On a film camera, I...

Questions in other subjects:

Konu
SAT, 19.10.2019 15:30