Computers and Technology

Computers and Technology, 14.09.2019 01:10, que81hhh

What commands will reset a network interface in linux?

answer

Answers: 3

Show answers

Similar questions

Предмет

Computers and Technology, 22.09.2019 10:30, michellen2020

Informs the network interface card to pass packets sent to that address to the ip stack so their contents can be read, and tells the ip gateway to forward such traffic onto the physical network, where the listening network interface resides.

Answers: 1

Предмет

Computers and Technology, 08.10.2019 02:20, peachesmims1991

The network board in a workstation is currently configured as follows: - network speed = auto- duplexing = autothe workstation is experiencing poor network performance, and you suspect that the network board is not correctly detecting the network speed and duplex settings. upon investigation, you find hat it is running at 10 mbps half-duplex. you know that your network switch is capable of much faster throughout. to fix this issue, you decide to manually configure these settings on the workstation.before you do so, you need to verify the configuration of the switch port that the workstation is connected to. given that it is a cisco switch, which commands can be used on the switch to show a list o all switch ports and their current settings. (select two.)a. show running-config interfaceb. show interface ethernet countersc. show interface switchportd. show interfacee. show interface capabilities

Answers: 3

Предмет

Computers and Technology, 30.10.2019 06:31, courtneygaffney4755

Apc is not able to connect to a wired network. pinging the loopback address is successful, but the gateway cannot be reached. on the network switch all the interface lights are on, except for the interface connected to the pc. the led on the network card is off. what is the most likely cause of this problem?

Answers: 3

Предмет

Social Studies, 13.11.2019 05:31, jimarieb08

You are configuring a linux system for 10 different users. before you create the user accounts, you need to ensure that specific commands execute clean up tasks when the user logs out of the linux system. you want to reduce redundant actions by configuring the commands once for all users that will be created on the system. where should you configure the commands?

Answers: 1

Do you know the correct answer?

What commands will reset a network interface in linux?...

Questions in other subjects:

Konu

Mathematics, 21.08.2019 23:00

Could you solve me this exercice: : 3 you a lot! : 3 : 3 : 3...

Konu

Mathematics, 21.08.2019 23:00

On a math course, a student scored 95 on the test, 92 on the second test, 83 on the third test, 75 on the fourth test and 53 on the fifth test and 70 on the last test. if the stude...

Konu

Biology, 21.08.2019 23:00

Older sedimentary rocks are usually found above younger ones. true false...

Konu

Mathematics, 21.08.2019 23:00

What is 3 3/2 equal to ? a . 3 sqrt 9 b . 2 sqrt 9 c.3 sqrt 27 d. 2 sqrt 27...

Konu

English, 21.08.2019 23:00

Which line shows conflict? i had stupidly hoped to make things better between us with a series of gifts and poems. she had a blue dress and a tan hat on the day i met her in the g...

Konu

Geography, 21.08.2019 23:00

What time is it florida if you live in a different place in iceland?...

Konu

Health, 21.08.2019 23:00

Which of the following is true concerning stretching techniques? a. ballistic stretching exercises never involve bouncing. b. you should always stretch before warming...

Konu

Advanced Placement (AP), 21.08.2019 23:00

2. why does government usually try to prevent monopolies from forming?...

Konu

Mathematics, 21.08.2019 23:00

The sum of a number and its square is 42. which equation can be used to find the two numbers for which this is true? x^2 + x = 42 x^2 + 2x = 42 x^2 + x + 42 = 0

Konu

Social Studies, 21.08.2019 23:00

What is a synonym for indirect rule...

Other tasks in the category: Computers and Technology More task